Home » Products » e²BMS

e²BMS

The ABERTAX® e²BMS is another quality product from Abertax Technologies. It gives essential battery information i.e. full voltage, half voltage, temperature and electrolyte level. It stores the number of charge/discharge cycles, temperature, electrolyte low level duration and deep discharge duration. The e²BMS is a state-of-the-art wireless technology for operation cost-cutting and providing a quality service. Data communication is done via RF.

 

The e²BMS has 3 LED’s, which indicate the following:

–        Flashing green: when powered and no warnings
–        Flashing red: electrolyte level below specified minimum for flooded batteries and low voltage
–        Flashing yellow: battery temperature above 50°C
 
 
Contact Form with Product request
 

e²BMS standard with CLS, temperature sensor and hall sensor

The ABERTAX® e²BMS - STANDARD is our advanced version for battery monitoring. The communication between user interfaces and the devices is made by a RF technology. Three LEDs are integrated in a 130 x 45 x 25 mm housing that can be placed on top of the battery cells. The external level probe can be placed in the centre of the battery. The temperature sensor can either be placed outside or inside the cell. A full and half voltage reading is available. Actual and accumulated battery data is stored inside the BMS and can be uploaded via a RF interface to the PC.

-        Integrated LED's
-        external level probe
-        Gauge Guard or O-Ring
-        Temperature sensor inside or outside cell
-        Full and half voltage reading
-        Current measurement with hall sensor
-        RF wireless communication
-        Various connector types

Rating:
X

Asc To Seller

    • Battery Technology :
    • Lead-Acid (Open Type or VRLA)
    • Input / Supply Voltage :
    • Rated Voltage ±50%
    • Max. Operating Volt. (24V - 80VDC nom.) :
    • 120VDC
    • Min. Operating Volt. (24V - 80VDC nom.) :
    • 12VDC
    • Current Consumption 24VDC :
    • 30mA avg., 90mA pk during GPRS data transmission
    • Current Consumption 36VDC :
    • 22mA avg., 66mA pk during GPRS data transmission
    • Current Consumption 48VDC :
    • 15mA avg., 45mA pk during GPRS data transmission
    • Current Consumption 80V DC :
    • 10mA avg., 30mA pk during GPRS data transmission
    • Max. Current measurement range :
    • ±900A
    • Operational Temp. Range :
    • -30°C to +70°C
    • Communication :
    • 2.4 GHz Wireless MiWi Protocol through USB 2.0, GPRS over 2G GSM 850 / 900 (Dual Band) or 850 / 900 / 1800 / 1900 (Quad Band)
    • Temp. Sensor Range :
    • -40°C to +100°C
    • Relative Humidity in Operation :
    • 95% no dew
    • Relative Altitude :
    • Up to 2000m ASL
    • Protection class :
    • IP65
    • Length CLS probe :
    • 77mm or 127mm
    • CLS type :
    • GaugeGuard or O-Ring
    • Diameter hole for Gauge Guard :
    • 10mm (M10 drill)
    • Temperature probe type :
    • inside or outside cell
    • Dimensions (L x W x H) :
    • 130 x 45 x 25 mm ± 0.5 mm, (excluding cables & sensors)
    • Weight w. stand. version approx. :
    • 200g
    • Brochure (PDF) :
    • ​ View
Print this information

  • Select Product Options

    Please select company type in the mentioned groups.

    Please enter your country.

    Product Definition

    Please select the type of e2BMS you want to use. The online version has RF and GPRS communication. The standard Version has RF communication. As an Option you can choose a hall sensor for current measuring.

    Please select the type of Battery the e2BMS will be used on. The version for flooded batteries includes a CLS and thermal sensor for the battery. The AGM/GEL Version only has a thermal sensor for the battery.

    Please enter the battery capacity in C5

    Enter another DC voltage if not available in the selection above. Maximum nominal voltage is 80VDC. Minimum voltage 12VDC.

    Choose your battery pole connector type. We recommend the following: WLW – Bolted battery connectors Terminal Connector – Welded battery connectors Standard – Usage of own battery connector

    Select the CLS probe length (if any) you require or enter the specific length in the field below

    If you need a specific length of the CLS probe, please specify the length of the probe, measured from the top of the battery lid to the top of the battery plates.

    Here you can select if you require and external LED indication for the CLS

    Please enter any comments to your request.

    My consent into commercial communication

    I would like to be commercially contaced by ABERTAX Group of companies through the following communication channels. For details please see our Data Privacy Statement.

    You confirm that you have read the Data Security Statement of Abertax and agree that your contact data is stored according the Data Security Statement. Your consent can be rewoked by sending an email to datasecurity@abertax.com.

Abertax Technologies Ltd.

KW17A, Corradino Industrial Estate
PLA3000, Paola, Malta

Legal Disclaimer
Data Privacy Statement
Phone, Fax, Email

Phone: +356 23 678100
Fax: +356 21 808 625
Email: info@abertax.com